最新的Network Appliance NS0-182免費考試真題

問題1

You install and apply the NetApp RSCF on cluster interconnect switches.
Which two statements are correct in this scenario? (Choose two.)

A. The RCF file enables CDP to allow connected devices to discover the switch.

B. The RCF file enables flow control and is set to receive.

C. The RCF file enables IPv6 for use by the cluster traffic.

D. The RCF file enables jumbo frames for all cluster traffic.

正確答案: C,D

問題2

You are creating an aggregate on a new FAS8200 with two DS224C shelves. Your customer wants to be able to use the Disk Maintenance Center.
In this scenario, what is the minimum number of spare disks required per node and disk type?

A. 3

B. 4

C. 2

D. 1

正確答案: C

問題3

You were dispatched to add a DS224C to an existing HA pair that has a stack of DS4243 shelves with 1 TB drives and a stack of DS4246 shelves with 1 TB drives. The customer wants to make sure that ACP is cabled for all shelves.
Which two considerations should you advise the customer in this situation? (Choose two.)

A. ACP communication cannot be used for the DS224C and the DS4243 shelves at the same time.

B. The ACP communication has been discontinued beginning with ONTAP 9.5, IOM6, and IOM12 modules.

C. ACP communication uses SAS cables and does not require Ethernet cables for IOM12 and IOM6 modules.

D. Out-of-band ACP communication is use by default in ONTAP 9.0 and later software.

正確答案: C,D

問題4

After the installation of the NetApp CN1610 cluster switches, you want to verify that the cabling is correct.
Which protocol will allow you to verify the cabling remotely?

A. Transmission Control Protocol (TCP)

B. Cisco Discovery Protocol (CDP)

C. Point to Point protocol (PPP)

D. Hyper Text Transfer Protocol (HTTP)

正確答案: A

問題5

Starting with ONTAP 9.5, what is the maximum number of HA pairs that are supported when using a SAN cluster?

A. 8

B. 4

C. 2

D. 6

正確答案: B

問題6

You have a 4-node FAS8060 cluster. You are using the vol move command to relocate a volume from an aggregate on node 1 to an aggregate on node 4.
In this scenario, which network is used for the traffic being relocated?

A. the cluster interconnect

B. the intercluster network

C. the HA interconnect

D. the node management network

正確答案: A

問題7

Without adding new cluster interconnect switches, you want to nondisruptively upgrade from FAS2554 controllers to FAS8200 controllers on an existing 2-node switchless cluster running ONTAP 9.5 software.
Which statement is correct in this scenario?

A. Set up the FAS8200 as a new cluster, move the SVMs from the FAS2554 to the FAS8200 using SVM move, and decommission the FAS2554.

B. Connect the FAS8200 to the FAS2554 with interconnect cables, join the existing cluster, relocate the aggregates from the FAS2554 to the FAS8200, and decommission the FAS2554.

C. You cannot perform this task nondisruptively.

D. Relocate the aggregates to one FAS2554 node, takeover, replace the node in takeover state with a FAS8200 node, reassign the disks, giveback, and repeat for the second node.

正確答案: D

問題8

You just finish the installation of a single-node cluster. You want to make sure that the cluster backups are saved to a different location.
What is required to accomplish this task?

A. Configure a system configuration backup.

B. Enable copy offloading.

C. Set up SVM disaster recovery.

D. Set up AutoSupport

正確答案: A

問題9

You have just installed a new AFF A220 4-node cluster with ONTAP 9.5 for a customer.
Which two cluster switches are supported in this scenario? (Choose two.)

A. Cisco MDS 91485

B. NetApp CN1610

C. Cisco Nexus 5596UP

D. Brocade 6510

正確答案: B,C

最新的Network Appliance NetApp Certified Storage Installation Engineer, ONTAP - NS0-182免費考試真題

聯系我們

站內鏈接

最新更新