最新的HP HPE2-Z39免費考試真題

問題1

A network administrator needs to reach an ArubaOS switch CLI at a management IP address. The administrator also needs to ensure that the switch entirely rejects Telnet and
SSH connections from users in data VLANs. How can the administrator meet these goals?

A. Configure the management IP address on the OOBM port and configure the switch to listen for Telnet and SSH only on this port.

B. Configure the management IP address on the default VLAN and set a manager password.

C. Configure the management IP address on a VTY interface and bind an ACL to this interface.

D. Configure the management IP address on any VLAN except the default VLAN. Set a manager and operator password.

正確答案: B

問題2

An ArubaOS switch has the routing table shown in the exhibit. A network administrator then enters this command:
Switch (config) # ip route 10.1.8.0/24 10.1.12.8
Switch (config) # ip route 10.1.4.0/24 10.1.12.13
After the administrator enters this command, packets arrive that are destined for 10.1.12.8 and 10.1.12.13.
What does the switch do with this traffic?

A. It drops all of the traffic.

B. It forwards some of the traffic on VLAN 101 and some of the traffic on VLAN 4.

C. It forwards some of the traffic to 10.1.101.1 and drops some of the traffic.

D. It forwards all of the traffic to 10.1.104.2.

正確答案: C

問題3

Two ArubaOS switches connect on a VLAN. and both enable OSPF on that VLAN. Which
VLAN OSPF setting must match for the switches to become fully adjacent neighbors?

A. DR priority

B. router ID

C. cost

D. area ID

正確答案: B

問題4

A network administrator configures LLDP-MAD on an Aruba Virtual Switching Framework
(VSF) fabric. The administrator needs to enter an SNMP
community string after v2c in this command:
Switch:(config) # vat lldp-rnad ipv4 10.1.0.2 v2c ----------------
Which SNMP community string should the administrator enter?

A. one configured on the VSF fabric as a whole

B. one configured on the standby member in the fabric

C. one configured on the device at 10.1.0.2

D. one configured for the VSF fabric on AirWave

正確答案: B

問題5

A port on an ArubaOS switch has its default spanning tree settings.
When is the port defined as a spanning tree edge port?

A. when the switch runs MSTP but the connected switch runs RSTP

B. when the port is part of a VLAN that is dedicated to that port alone

C. when the switch and the connected switch run MSTP but have different region settings

D. when the port fails to receive BPDUs on the port within a set period of time

正確答案: A

問題6

What is a best practice for an MSTP region?

A. A switch should have a consistent spanning tree priority in each MSTP instance

B. The config name should contain the hostname of the root switch.

C. The desired root for the CIST should have a lower config revision than any other switch.

D. Switch-to-switch links should carry all VLANs in use in the MSTP region.

正確答案: D

問題7

Switch-1 and Switch -2 have the Virtual Switching Framework (VSF) settings shown in the exhibits.
The administrator then connects the switches together on the interfaces in the VSF link.
The administrator first enables VSF on Switch-1 and confirms the reboot. After
Switch-1 reboots, the administrator enables VSF on Switch-2 and confirms the reboot.
What happens?

A. Switch-1 and Switch-2 form a VSF fabric, and Switch-1 becomes the commander.

B. Switch-1 and Switch-2 fail to form a VSF fabric, and al interfaces on both switches remain up.

C. Switch-1 and Switch-2 form a VSF fabric, and all interfaces on Switch-1 are disabled.

D. Switch-1 and Switch-2 form a VSF fabric, and Switch-2 becomes the commander.

正確答案: C

最新的HP Fast Track - Applying Aruba Switching Fundamentals for Mobility - HPE2-Z39免費考試真題

聯系我們

站內鏈接

最新更新