最新的EMC Dell PowerEdge Professional - DCPPE-200免費考試真題
An engineer enters a data center to configure an uplink between an I/O Aggregator (IOA) and an upstream switch. The IOA and upstream switch are configured for spanning tree. The engineer applies the following configuration to the uplink port:
interface TenGigabitEthernet 0/12
switchport
flowcontrol rx on tx off
spanning-tree rstp edge-port
As soon as the engineer plugs in the cables, it creates a loop and brings down the network.
Which commands should be entered on the IOA to fix loop?
interface TenGigabitEthernet 0/12
switchport
flowcontrol rx on tx off
spanning-tree rstp edge-port
As soon as the engineer plugs in the cables, it creates a loop and brings down the network.
Which commands should be entered on the IOA to fix loop?
正確答案: C
An engineer needs to assign two PCIe NICs and a GPU to a server node in a VRTX chassis.
Which two steps are required to complete this task? (Choose two.)
Which two steps are required to complete this task? (Choose two.)
正確答案: B,D
An engineer needs to update BIOS in the following environment:
- Over 100 servers are spread over 10 chassis
- All servers are in the same data center
- The only maintenance window is late Sunday evening when OS patches are applied and servers are rebooted
- Less than 10 minutes of additional downtime per server is allowed
What is the most effective update strategy?
- Over 100 servers are spread over 10 chassis
- All servers are in the same data center
- The only maintenance window is late Sunday evening when OS patches are applied and servers are rebooted
- Less than 10 minutes of additional downtime per server is allowed
What is the most effective update strategy?
正確答案: C
An engineer is redeploying a blade chassis, and is logged into the CMC web interface. The engineer has configured the iDRACs for the blade servers.
When the engineer tries to log into one of the iDRACs, the connection fails. The engineer can ping the CMC from the engineer's workstation but can NOT ping the iDRACs. The engineer tries to ping the iDRAC IP from the CMC itself using the diagnostic tool, but that also fails.
Which two tasks should the engineer perform? (Choose two.)
When the engineer tries to log into one of the iDRACs, the connection fails. The engineer can ping the CMC from the engineer's workstation but can NOT ping the iDRACs. The engineer tries to ping the iDRAC IP from the CMC itself using the diagnostic tool, but that also fails.
Which two tasks should the engineer perform? (Choose two.)
正確答案: D,E
An engineer is installing a server node with a quad port 1GbE NIC into SLOT 3 on a VRTX chassis with a
1GbE Pass-Through Module (PTM) in Fabric A.
During POST of this server, a message indicates that ports 3 and 4 of the NIC are being disabled. The system completes the boot process and is otherwise operational.
What is causing this message?
1GbE Pass-Through Module (PTM) in Fabric A.
During POST of this server, a message indicates that ports 3 and 4 of the NIC are being disabled. The system completes the boot process and is otherwise operational.
What is causing this message?
正確答案: A
A password to the CMC root account on an M1000e server chassis has been misplaced.
What should be done to restore administrative access to the CMC?
What should be done to restore administrative access to the CMC?
正確答案: C
An engineer needs to configure a single network port on a 10 GbE NIC for four virtual network interfaces.
What steps should the engineer perform to complete this task?
What steps should the engineer perform to complete this task?
正確答案: C
An engineer is installing two PCIe NICs into an existing VRTX chassis. Node 1 has three PCIe cards assigned to it already. After installation, the engineer is unable to assign the two new NICs to node 1.
What should the engineer do to assign the two PCIe NICs to node 1?
What should the engineer do to assign the two PCIe NICs to node 1?
正確答案: B
An engineer is installing a known good PCIe storage adapter in SLOT 1 of an FX2 chassis with four half height nodes. Node 1 is NOT detecting the adapter.
What must the engineer do so that node 1 can detect the adapter?
What must the engineer do so that node 1 can detect the adapter?
正確答案: A
An engineer needs to configure a full height blade server and iSCSI traffic. The blade has two dual port NDCs.
The M1000e chassis only has switches in A fabric.
A1 - Production traffic:
174.1.0.0/16 network
Server facing switch ports use tagged VLANs 10, 30, 50
A2 - iSCSI traffic:
10.0.0.0/24 network
Untagged traffic
Switch is set to access VLAN 20
The engineer needs to set up the host to operate on the iSCSI network using two ports.
Which ports should be used?
The M1000e chassis only has switches in A fabric.
A1 - Production traffic:
174.1.0.0/16 network
Server facing switch ports use tagged VLANs 10, 30, 50
A2 - iSCSI traffic:
10.0.0.0/24 network
Untagged traffic
Switch is set to access VLAN 20
The engineer needs to set up the host to operate on the iSCSI network using two ports.
Which ports should be used?
正確答案: D