最新的Cisco 500-220免費考試真題

問題1

What are two ways peers interact with ports that Auto VPN uses? (Choose two.)

A. Peers contact the VPN registry at TCP port 9350.

B. Peers contact the VPN registry at UDP port 9350.

C. For IPsec tunneling, peers use UDP ports 500 and 4500.

D. For IPsec tunneling, peers use high TCP ports within the 32768 to 61000 range.

E. For IPsec tunneling, peers use high UDP ports within the 32768 to 61000 range.

正確答案: B,E

說明：（僅 Fast2test 成員可見）

問題2

Refer to the exhibit.

Which condition or conditions will cause the " All Databases & cloud services " SD-WAN traffic to be routed via a VPN2 tunnel on WAN2?

A. WAN1 tunnel latency is 20 ms or more, and WAN2 tunnel meets the configured performance criteria.

B. WAN1 tunnel latency is 20 ms or more, irrespective of WAN2 tunnel performance.

C. WAN1 tunnel latency is 20 ms or less, irrespective of WAN2 tunnel performance.

D. WAN1 tunnel latency is 20 ms or less, and WAN2 tunnel meets the configured performance criteria.

正確答案: A

說明：（僅 Fast2test 成員可見）

問題3

Which technique is not a PCI requirement but is considered a best practice for limiting the cardholder data environment (CDE) from the remainder of a corporate network?

A. Incorporate the CDE within the corporate network ' s established Demilitarized Zone (DMZ).

B. Limit inbound connections to the CDE while allowing all outbound connections originating from the CDE.

C. Implementing identical firewall rules between corporate and CDE egress points.

D. Establishing wired network segmentation between the CDE and the rest of the corporate network.

正確答案: D

說明：（僅 Fast2test 成員可見）

問題4

Which order is accurate for a firmware upgrade on MX appliances in a high-availability configuration?

A. starts on both MX appliances at the same time and then reboots both appliances after traffic on the primary MX appliance ceases

B. starts on both MX appliances at the same time and then immediately reboots both appliances

C. starts on the primary MX appliance and then occurs on the secondary MX appliance

D. starts on the secondary MX appliance and then occurs on the primary MX appliance

正確答案: C

說明：（僅 Fast2test 成員可見）

問題5

Which design requirement is met by implementing syslog versus SNMP?

A. when proactive alerts for critical events must be generated

B. when information such as flows and client connectivity must be gathered

C. when automation capabilities are needed

D. when organization-wide information must be collected

正確答案: B

說明：（僅 Fast2test 成員可見）

問題6

Where should a network admin navigate to investigate wireless mesh information between Meraki APs?

A. Wireless > Configure > Radio Settings

B. Wireless > Monitor > Wireless Health

C. Wireless > Monitor > Access Points > AP > RF

D. Wireless > Monitor > RF Spectrum

正確答案: C

說明：（僅 Fast2test 成員可見）

問題7

Refer to the exhibit.

For an AP that displays this alert, which network access control method must be in use?

A. WPA2-enterprise with my RADIUS server

B. splash page with my RADIUS server

C. MAC-based access control with RADIUS server

D. preshared key

正確答案: A

說明：（僅 Fast2test 成員可見）

問題8

When wireless SSIDs are configured in Dashboard, which setting on the Access Control page affects the ability of a 2.4 GHz only client device from associating to the WLAN for the first time?

A. Content filtering

B. 802.11r

C. Bridge mode

D. Dual band operating with Band Steering

正確答案: D

說明：（僅 Fast2test 成員可見）

問題9

Which API endpoint clones a new Organization?

A. PUT /organizations/{organizationId}/clone

B. POST /organizations/{organizationId}/clone

C. POST /organizations/clone/{organizationId}

D. POST /organizations/{organizationId}/new

正確答案: B

說明：（僅 Fast2test 成員可見）

最新的Cisco Engineering Cisco Meraki Solutions - 500-220免費考試真題

聯系我們

站內鏈接

最新更新