最新的Cisco 300-615免費考試真題

問題1

Refer to the exhibit.

The job fails to run. Which action resolves the issue?

A. Add a start time to the script

B. Enable the feature required

C. Configure an NTP server

D. Renew the feature license

正確答案: B

說明：（僅 Fast2test 成員可見）

問題2

A network engineer notices a sudden interruption to the HSRP adjacency between the switches. The packet loss is reported on the servers for which the default gateway is set as the virtual IP of the HSRP. AII servers on the VLAN can exchange ping messages. Which configuration set must be applied on the HSRP peers to resolve the adjacency issue?

A. key1 accept-lifetime 00:00:00 Jun 01 2018 23:59:59 Sep 01 2020

B. key 1 send-lifetime 00:00:00 Jun 01 2018 23:59:59 Sep 01 2022

C. key 0 accept-lifetime 00:00:00 Oct 01 2018 23:59:59 Sep01 2020

D. key 0 send-lifetime 00:00:00 Oct 01 2018 23:59:59 Sep 01 2020

正確答案: A

說明：（僅 Fast2test 成員可見）

問題3

A system administrator connects a Cisco Nexus 2248PQ FEX to a fabric interconnect to expand the ports that are available for connecting Cisco UCS C-Series Rack Servers. In Cisco UCS Manager, the administrator does not see the servers connected to this FEX. Which action should be taken to resolve the issue?

A. The FEX must be exchanged so that it supports the connectivity between fabric interconnects and UCS CSeries servers

B. The ports that connect the FEX to the fabric interconnects must be configured as server ports

C. The transceivers must be exchanged to support the connectivity between the FEX and the fabric interconnects

D. The fabric interconnects must be rebooted before the FEX is recognized

正確答案: B

說明：（僅 Fast2test 成員可見）

問題4

Refer to the exhibit.

The connection between a Cisco Nexus 5548UP switch and a Cisco MDS switch fails to initialize. What is the cause of the issue?

A. Trunk mode must be activated.

B. The SFP is unsupported.

C. VSAN 1 is suspended.

D. The interface is in an incorrect mode.

正確答案: C

說明：（僅 Fast2test 成員可見）

問題5

An attempt to use a global vNIC redundancy template pair results in a service profile that fails to apply.
Which action resolves the issues?

A. Assign the primary template first, and then set the peer name.

B. Assign both templates simultaneously.

C. Assign the secondary template first, and then set the peer name.

D. Create the peer names before creating the templates.

正確答案: A

說明：（僅 Fast2test 成員可見）

問題6

The Cisco UCS Manager fails to integrate with Cisco Intersight. The requirement is to monitor and configure the UCS environment from UCS Manager as well as Cisco Intersight. However, Cisco Intersight can monitor only the managed devices. Which action resolves the issue?

A. Allow Cisco IMC IP addresses of all the managed servers to reach Cisco Intersight.

B. Set the Access Mode of Intersight Connector on the UCS to Allow Control.

C. Change the configured DNS server to resolve the Cisco Intersight IP address.

D. Update the NTP settings on all the devices that Intersight manages to be in the same time zone.

正確答案: B

說明：（僅 Fast2test 成員可見）

問題7

Refer to the exhibit.

An engineer configures the server port on a Cisco Nexus 5000 Series Switch. The switch connects to an NPV edge switch port. The server fails to send the FC traffic to the fabric. Which action resolves the issue?

A. Enable the NPIV mode on the Cisco Nexus 5000 switch.

B. Replace the SFP in slot fc2/12.

C. Configure the BB_credit buffer on the uplink port.

D. Match the VSAN membership on both ends of the connection.

正確答案: A

說明：（僅 Fast2test 成員可見）

問題8

An IOM fails during a firmware upgrade and is unresponsive. Which action recovers the module?

A. B . Reset the faulty module from the peer IOM

B. C . Reinstall the firmware using Auto Install .

C. D . Restore the Cisco UCS Manager configuration from backup .

正確答案: B

說明：（僅 Fast2test 成員可見）

問題9

A server fails to boot from the operating system after a RAID1 cluster migration. The RAID remains in an inactive state during and after a service profile association. Which action resolves the issue?

A. Configure the SAN boot target to any configuration mode.

B. Use a predefined local disk configuration policy.

C. Configure the SAN boot target in the service profile.

D. Remove the local disk configuration policy.

正確答案: B

說明：（僅 Fast2test 成員可見）

最新的Cisco Troubleshooting Cisco Data Center Infrastructure - 300-615免費考試真題

聯系我們

站內鏈接

最新更新