最新的Cisco 200-601免費考試真題

問題1

Refer to the exhibit.

All of the vlans listed in the routing table below are trunked using 802.1q and are active on all switches. PLC1, PLC2, and PLC3 each has IP address 192.168.0.1/24 and are connected to ports configured for vlan 50. L2SW1, L2SW2, and L2SW3 are not using vlan trunking for vlan 50.
L3SW1 has following routing table:
10.0.0.0/8 is variably subnetted, 12 subnets, 2 masks
C 10.3.138.0/23 is directly connected, Vlan307
C 10.3.136.0/23 is directly connected, Vlan306
C 10.15.153.0/24 is directly connected, Vlan398
C 10.3.142.0/23 is directly connected, Vlan309
C 10.3.140.0/23 is directly connected, Vlan308
C 10.3.186.0/23 is directly connected, Vlan293
C 10.15.154.0/24 is directly connected, Vlan399
C 10.3.184.0/23 is directly connected, Vlan292
C 10.3.190.0/23 is directly connected, Vlan295
C 10.3.188.0/23 is directly connected, Vlan294
C 10.3.182.0/23 is directly connected, Vlan291
C 10.3.180.0/23 is directly connected, Vlan290
PLC1, PLC2, and PLC3 cannot be reconfigured. What can be done to be able to simultaneously communicate with PLC1, PLC2, and PLC3?

A. Enable NAT on L2SW1 - L2SW3

B. Enable NAT on L2SW4

C. Add vlan 50 to L2SW4 and assign the administrator's an IP address on 192.168.0.0/24 network

D. Enable NAT on L3SW1

正確答案: A

問題2

Refer to the exhibit.

Which three options are needed to configure NAT on router GW so PC1 and PC2 will be able to ping 203.0.113.1? (Choose three)

A. interface Ethernet0
ip nat inside
interface Ethernet1
ip nat outside

B. ip nat inside source list ACL_NAT interface Ethernet1 overload

C. ip access-list standard ACL_NAT
permit 10.1.1.0 0.0.0.255

D. ip nat inside source static tcp 10.1.1.0 80 interface Ethernet1 80

E. interface Ethernet0
ip nat outside
interface Ethernet1
ip nat inside

F. ip access-list extended ACL_NAT
permit tcp 10.1.1.0 0.0.0.255 any eq 80

正確答案: A,B,C

問題3

If the Link Fault alarm is connected to the minor relay and the FCS Bit Error Rate alarm is connected to the major relay, which commands will create an alarm profile called GigE with the alarms correctly mapped to the minor and major relays?

A. Switch(config)#alarm profile GigE
Switch(config-alarm-prof)#alarm 1 3
Switch(config-alarm-prof)#relay major 3
Switch(config-alarm-prof)#relay minor 1

B. Switch(config)#alarm profile GigE
Switch(config-alarm-prof)#alarm 1 4
Switch(config-alarm-prof)#relay major 4
Switch(config-alarm-prof)#relay minor 1

C. Switch(config)#alarm profile GigE
Switch(config-alarm-prof)#alarm 1 4
Switch(config-alarm-prof)#relay major 1
Switch(config-alarm-prof)#relay minor 4

D. Switch(config)#alarm profile GigE
Switch(config-alarm-prof)#alarm 1 3
Switch(config-alarm-prof)#relay major 1
Switch(config-alarm-prof)#relay minor 3

正確答案: B

問題4

What are the two most relevant factors in determining the class of administration that is required to maintain the telecommunications infrastructure? (Choose two.)

A. the industry that the infrastructure supports

B. the size of the infrastructure

C. the complexity of the infrastructure

D. the physical environment of the infrastructure

E. the age of the infrastructure

正確答案: B,C

問題5

DRAG DROP

正確答案:

問題6

Which describes the relationship between a workgroup bridge?

A. Wireless clients of a controller-based access point can communicate with wired clients of a workgroup bridge, but Wireless clients of an autonomous access point cannot communicate with wired clients of a workgroup bridge

B. Wireless clients of an autonomous access point can communicate with wired clients of a workgroup bridge, but Wireless clients of a controller-based access point cannot communicate with wired clients of a workgroup bridge

C. Wired clients of a workgroup bridge can communicate, through the workgroup bridge, with wireless clients of an autonomous or a controller-based access point

D. Wireless clients of a controller-based AP can communicate, through the workgroup bridge, with wireless clients of an autonomous access point

正確答案: C

問題7

Which CLI command will display IGMP snooping information in a Cisco IE2000 or Stratix 5700 switch?

A. switch#show ip igmp snooping

B. switch#show igmp snooping

C. switch#show snooping ip igmp

D. switch#show ip snooping

正確答案: A

問題8

Which is an issue with running CIP Motion on a REP network and identifies an alternate resiliency protocol that works for CIP Motion?

A. REP convergence is not fast enough. DLR is a suitable resiliency protocol for CIP motion.

B. CIP Motion requires a star topology which is not supported by REP. DLR is a suitable resiliency protocol for CIP motion.

C. REP convergence is not fast enough. RPVST+ is a suitable resiliency protocol for CIP motion.

D. CIP Motion requires a star topology which is not supported by REP. RPVST+ is a suitable resiliency protocol for CIP motion.

正確答案: A

問題9

Which command globally enables QoS on a Cisco Industrial Ethernet switch?

A. switch(config)#mls qos

B. switch(config)#mls queuing enable

C. switch(config)#qos enable

D. switch#enable queuing

正確答案: A

最新的Cisco Managing Industrial Networks for Manufacturing with Cisco Technologies - 200-601免費考試真題

聯系我們

站內鏈接

最新更新