最新的IBM 000-121免費考試真題

問題1

What are the three types of network adapters that can be assigned to an IBM i client partition?

A. An Ethernet adapter in a PCIe slot A Host Ethernet Adapter A virtual Ethernet adapter

B. A Fibre Channel over Ethernet adapter An Ethernet adapter in a PCIe slot A Serial over LAN adapter

C. A client connect adapter A virtual Opticonnect adapter A Fibre Channel over Ethernet adapter

D. An Ethernet adapter A virtual Fibre Channel adapter A Host Ethernet Adapter

正確答案: A

問題2

What is the purpose of Tagged I/O in a partition profile?

A. To specify critical hardware elements, without which the profile cannot be loaded or run

B. To allow the HMCto identifythe load source disk unit

C. To specifywhich hardware elements are available to be shared using NPIV

D. To configure vLANs on Host Ethernet Adapters

正確答案: A

問題3

What are two methods to determine the partition to which virtual disks are assigned?

A. In VIQ Server, use the Isctg -vI command In IBM i, use the WRKHWDRSC *STG command

B. In VIO Server, use Ispv-AvI In the HMC command line, use Isvdev-p

C. In VIO Server, use the Ismap command In the HMC GUI use Virtual Resources/Virtual Storage Management

D. In VIO Server, use Isdev-v command In IBM i, use WRKCFRGSTS *DEV* VRT

正確答案: C

問題4

A POWER7 server is being configured with 1 hosting IBM i partition and 4 client IBM i partitions. All partitions will run IBM i 7.1, TR4. The hosting partition is providing network support to the client partitions and needs both redundancy and best bandwidth.
What connectivity on the host partition will support these requirements?

A. Configure two or more Ethernet lines. Create a Virtual IP address for the host partition. Configure Showler routes to the local network for load balancing.

B. Configure two or more Ethernet lines. Use the lines to create redundant bridges to the internal vLANs used by the client partitions.

C. Using two or more physical Ethernet resources configure an aggregated link to the switch and use this for the bridge to the internal vLANs used by the client partitions.

D. Using two or more physical Ethernet resources configure an aggregated link to the switch and use this for IP address of the host partition.

正確答案: C

問題5

While creating a new partition and choosing appropriate I/O resources, nothing appears on the Tagged I/O screen to be selected as a "Load Source." Which of the following could cause this to happen?

A. Supported resources for a load source adapter have not been included in the profile.

B. The disk attached to the controller is not powered-on.

C. The CEO is not in "standby' mode.

D. Resources are only marked as Desired, not as Required.

正確答案: D

問題6

The DSPFMWSTS on an IBM i 7.1 partition appears as shown:

As part of troubleshooting, IBM support asks that level AL730_087 be deactivated.
How is that accomplished?

A. On the resulting screen, select the managed system Under Tasks select Change Licensed Internal Code for Current Release In the wizard select Deactivate Temporary Level

B. Stop all partitions Change the managed system to start in "P" mode Restart the managed system From the HMC, select Updates

C. Run command RMVPTF LICPGM(5770SS1) SELECT(MH01310) DELAYED(*YES), then restart the partition

D. Run command DLTPTF PTF(MH01310) RMV(*TEMP)

正確答案: B

問題7

An IBM i 7.1 partition hosts another IBM i 7.1 partition. The hosting partition provides disk and networking services for the client partition.
An operator restarts the host partition from the HMC.
What happens to the client partition?

A. It crashes and requires a Main Storage Dump before manually restarting.

B. It IPLs automatically.

C. It hangs and has to be manually restarted.

D. It halts with a SRC indicating missing disks, and resumes when the host restarts.

正確答案: D

最新的IBM Virtualization Technical Support for IBM i -v1 - 000-121免費考試真題

聯系我們

站內鏈接

最新更新