最新的Juniper JN0-363免費考試真題

問題1

You are asked to configure filter-based forwarding on a Junos device.
Which two statements are correct in this scenario? (Choose two.)

A. You must create a routing policy.

B. You must create a routing instance.

C. You must create a route target.

D. You must create and apply a match filter.

正確答案: A,D

說明：（僅 Fast2test 成員可見）

問題2

Which statement is correct about IS-IS?

A. IS-IS is a path vector routing protocol.

B. IS-IS is a classful routing protocol.

C. IS-IS is a link-state routing protocol.

D. IS-IS is a distance vector routing protocol.

正確答案: C

說明：（僅 Fast2test 成員可見）

問題3

Exhibit

You are asked to configure OSPF between routers R1 and R2 using IPv6 addresses.
Which two tasks will accomplish your objective? (Choose two.)

A. Issue the sec protocols ospf area 0.0.0.0 interface ge-0/0/1.0 command.

B. Under the [edit routing-options] hierarchy, configure a 128-bit router ID.

C. Under the [edit routing-options] hierarchy, configure a 32-bit router ID.

D. issue the set protocols ospf3 area 0.0.0.0 interface ge-0/0/1.0 command.

正確答案: C,D

說明：（僅 Fast2test 成員可見）

問題4

Exhibit

You configured interface ge-0/070.0 to run IS-IS. but this interface does not appear in the output of the show isis adjacency command as shown in the exhibit.
What is the problem in this scenario?

A. The family iso statement must be added to the logical interface.

B. The router at the other end of the link Is not sending any IS-IS Hello messages.

C. This is a Gigabit Ethernet interface, that is incompatible with the reference-bandwidth 100g statement.

D. The router at the other end of the link is a Level 1 only router.

正確答案: A

說明：（僅 Fast2test 成員可見）

問題5

Exhibit

Which two statements are correct about the information shown in the exhibit? (Choose two.)

A. The root bridge's priority Is 4k.

B. This switch is the root bridge for this spanning tree topology.

C. The root bridge is reachable using the ge-0/0/14 interface.

D. This switch has a bridge priority of 8k.

正確答案: C,D

說明：（僅 Fast2test 成員可見）

問題6

What are two types of SIDs used in segment routing? (Choose two.)

A. link

B. node

C. adjacency

D. interface

正確答案: B,C

問題7

What is the correct order of BGP attributes for active route selection?

A. next hop -> local preference -> AS path -> MED -> origin

B. next hop -> AS path -> local preference -> origin -> MED

C. next hop -> local preference -> AS path -> origin -> MED

D. next hop -> origin -> local preference -> AS path -> MED

正確答案: C

說明：（僅 Fast2test 成員可見）

問題8

Which two statements are correct about IS-IS? (Choose two.)

A. A level 1 only router can form an adjacency with a level 2 only router.

B. A level 1 only router can never form an adjacency with a level 2 only router.

C. For level 2 adjacencies, the area IDs must be the same.

D. For level 2 adjacencies, the area IDs can be different.

正確答案: B,D

說明：（僅 Fast2test 成員可見）

問題9

Exhibit

You want the R1 and R3 routers to forward traffic destined to the 203.0.113.0/24 network through R2. Which BGP attribute would you modify to satisfy this requirement?

A. origin

B. community

C. local preference

D. MED

正確答案: D

說明：（僅 Fast2test 成員可見）

最新的Juniper Service Provider Routing and Switching, Specialist (JNCIS-SP) - JN0-363免費考試真題

聯系我們

站內鏈接

最新更新